IQC工程師英文簡歷

時間：2024-10-19 17:20:21 英文簡歷模板我要投稿

相關推薦

IQC工程師英文簡歷模板

　　Name: Ms. YJBYS Gender: Female

IQC工程師英文簡歷模板

　　Wedlock: Single Nation: Han

　　Residence: Hunan-Changde Age: 27

　　Location: Guangdong-Guangzhou Height: 157cm

　　Target Locations: Guangdong-Guangzhou

　　Target Positions: Quality/Safety Management-QA/QC Manager/Supervisor

　　Quality/Safety Management-Supplier Quality Engineer

　　Industry/Factories-Project Engineer

　　Target Jobs: QA superior、 SQE/CQE、 project engineer

　　Desired Salary: 7500 RMB/month Negotiable

　　When Can Start: after 2013-08-16 later

　　Education

　　2008-09 ～ 2011-06 zhongshan university administration Bachelor Degree

　　Training

　　2013-04 ～ 2013-06 new oriental school cambridge speaking

　　2012-06 ～ 2013-04 sony electronics huanan co.,Ltd Japanese(level 3) Japanese(level 3)

　　2006-12 ～ 2007-03 foshan library public english test system PETS-3

　　2006-07 ～ 2006-11 foshan library Japanese(primary)

　　you are not full member,please contact us. (2010-08 ～ Present)

　　Company Type: Foreign Enterprise Company Category: Electrical,Micro-electronics

　　Job Title: supplier quality engineer Positions: Supplier Quality Assurance

　　Job Description: Company engages in the production of DVD laser writer, is a precise manufacturing, each product is assembled by 30 ~ 40 components(include hardware parts/electronic parts/optical parts). the major work during this period is supplier quality assurance, include that support supplier improving their quality and check quality system for keeping the stability.

　　1.evaluate the parts when new model is imported , discuss the demensions which are out of the spec. with the designer of headquarters in Japan, desinger will determine the ultimate judgement.

　　2.when new model begin to get in mass production, establish the document for parts on line and shipment.

　　3.According to the instruction of parts'approved specification and CTQ list ,establish the standard of inspection , educate the inspectors take the correct operation.

　　4.review the limited the samples which are submitted by suppliers, discuss with relevant departments, if that's necessary, must be taken test-run to verify. after getting the conclusion by discussion,submit it to designer to make the final decision.

　　5.handle the qualiy issues for parts' defect,if it gets great affect in production,must call an urgent meeting to discuss the further action.

　　6.evaluated suppliers's quality/server/cooperation etc ,got the list of up-steam suppliers,summarized their quality issues and established the plan for improvement.

　　7.implement AQAS audit based on the annual plan to verify supplier's quality system. (the auditor must get the qualification which is approved by Sony headquarters)

　　8.company begins to implement self-inspection plan to supplier, give some inforation to the suppliers and introduce its guidance(the detailed instructions must be explained again by quality manager), and according to the plan implement audits on-site, connect sony headquarters to issue certification for qualified suppliers.

　　9.establish QC flow for parts and make the managing plan for major suppliers base on headquarters's request.

　　10.some of projects which were encouraged by company had been involved.(such as:cost down PJ/success PJ,etc.)

　　Reason for Leaving: contract expiry

　　you are not full member,please contact us. (2007-12 ～ 2010-06)

　　Company Type: Foreign Enterprise Company Category: Electrical,Micro-electronics

　　Job Title: SQE Positions: Supplier Quality Engineer

　　Job Description: the company goes in for the production of thermal module , the component have many categories,for example,press/die-casting/extrusion/plastic,the major avail of the modules are used in VGA/DT/NB area,because of different parts with different process,so that ,incoming quality control include many contents, as below:

　　1.comfirm parts in trail run phase and feedback the information .

　　2.attend to the approval of new parts and PPAP's check.

　　3.collect incoming issues and confirm the corrective action in periodic time,which lead vendor to improve quality.

　　4.establish standard of inspection for product.

　　5.audit vendor's quality ,service ,cooperation and timely for 8D report reply,take advice require improvement.

　　6.deal with the defects parts after production,take negotiation with vendors,find out the responsibility and charge the cost,has saved nearly 3 million(RMB) for company in past two years.

　　Reason for Leaving: orders decreased result in the job without energy

　　you are not full member,please contact us. (2005-10 ～ 2007-11)

　　Company Type: Foreign Enterprise Company Category: Other Production,Manufacturing,Processing

　　Job Title: CQE/vice-director/SQE Positions: QA/QC Engineer

　　Job Description: the company engaged in the production of lens,in this period,job include(一)control the quality of lens material,this include spherical lens and non-spherical lens,the first one have simple process and purchase from domestic, and the second one's main source is from abroad.(二)lens process management,control some of characterist.(三)deal with customer's complain.

　　1.Take professional training for freshman.

　　2.evaluate the items for new parts run into control run phase and establish standard of operation.

　　3.Take quality tools work for data analysis,find out the method for solution.

　　4.Lead quality improve team.

　　5.evaluate and comfirm the quality issues,and take trace.

　　6.Accompany the auditor for check the company's procedure and work.

　　7.Control the quality of incoming product and manage vendors .

　　8.According different product establish inspection plan.

　　9.Establish the standard of operation and maintenance for equipments.

　　Reason for Leaving: company immigrate to WuHan

　　Project Experience

　　individual project leader (2011-03 ～ 2011-09)

　　Job Title: cost down PJ

　　Project Description: through decreasig supplier's stock ,shortened their inspection time and loosening the

　　quality standard under the condition of getting qualified verification to reach the purpose of cost down.

　　Responsibility: 1.organize team member,collect original data,analyse it.

　　2.according analysis result to identify the key factor in cost structure,evaluate the range of cost down and its possibility.

　　3.associate with team members to recheck the evaluation result,establish concrete plan for execution.

　　4.according verification result,discuss the rate how much can be taken cost down.

　　5.submit headquarters the evaluation report,the rate of cost down will be negotiated by headquarters procurement department.(20 million USD had been taken cost down in this PJ)

【IQC工程師英文簡歷】相關文章：